热轧相关英文文献求一篇完整的,有关热轧方面的英文文献,作者必须是外国的,一定要完整的哈,长度无所谓.还有重要的是带中文翻译（麻烦不要用在线翻译那种不流畅的）,满意的外加700分!

热轧相关英文文献求一篇完整的,有关热轧方面的英文文献,作者必须是外国的,一定要完整的哈,长度无所谓.还有重要的是带中文翻译（麻烦不要用在线翻译那种不流畅的）,满意的外加700分!
热轧相关英文文献
求一篇完整的,有关热轧方面的英文文献,作者必须是外国的,一定要完整的哈,长度无所谓.还有重要的是带中文翻译（麻烦不要用在线翻译那种不流畅的）,满意的外加700分!

热轧相关英文文献求一篇完整的,有关热轧方面的英文文献,作者必须是外国的,一定要完整的哈,长度无所谓.还有重要的是带中文翻译（麻烦不要用在线翻译那种不流畅的）,满意的外加700分!
求人不如求己!太专业.

你自己去百度找找呗

Hot-rolled
Advantages: can be destructive to ingot casting organizations, refined steel, grain, and the elimination of microstructure defects, thereby enabling organizations compacting steel, mec...

全部展开

Hot-rolled
Advantages: can be destructive to ingot casting organizations, refined steel, grain, and the elimination of microstructure defects, thereby enabling organizations compacting steel, mechanical properties were improved. This improvement is mainly reflected in the direction along the rolling up, so that steel is no longer up to a certain extent are isotropic body; pouring when the formation of bubbles, cracks and loose, but also at high temperatures and under stress by bonding.
Disadvantage: 1. After hot rolling, the steel's internal non-metallic inclusions (mainly sulphides and oxides, have silicate) was pressure into a thin, appears stratified (laminated) situation. Stratified so that along the thickness direction of steel tensile performance significantly deteriorated, and there is likely to shrink when weld tear between layers. Weld contraction induced by local strain often reach several times the yield point strain than the strain caused by a much larger load; 2. Uneven cooling caused by residual stress. Residual stress in the absence of external force are under the internal self-equilibrium stress and a variety of cross-section of hot-rolled steel have this kind of residual stress, the general beam section size the greater the greater the residual stress. Residual stress is self-equilibrium, but the external force on the steel members at the next performance or have a certain influence. Such as deformation, stability, anti-fatigue, etc. may have an adverse role. 3. Hot-rolled steel products, for the thickness and the wide side of good control in this regard.热胀冷缩our well-known, because of the beginning of the hot-rolled out of even length, the thickness of all targets, and finally cooled or negative must be bad, bad side of this negative more wide wide, the thickness of the thicker, the more obvious manifestations. So for the large steel, the steel edge wide, thickness, length, angle, and the line could not be very precise requirements.
好像有人回答了

收起

Hot-rolled
Advantages: can be destructive to ingot casting organizations, refined steel, grain, and the elimination of microstructure defects, thereby enabling organizations compacting steel, mec...

全部展开

Hot-rolled
Advantages: can be destructive to ingot casting organizations, refined steel, grain, and the elimination of microstructure defects, thereby enabling organizations compacting steel, mechanical properties were improved. This improvement is mainly reflected in the direction along the rolling up, so that steel is no longer up to a certain extent are isotropic body; pouring when the formation of bubbles, cracks and loose, but also at high temperatures and under stress by bonding.
Disadvantage: 1. After hot rolling, the steel's internal non-metallic inclusions (mainly sulphides and oxides, have silicate) was pressure into a thin, appears stratified (laminated) situation. Stratified so that along the thickness direction of steel tensile performance significantly deteriorated, and there is likely to shrink when weld tear between layers. Weld contraction induced by local strain often reach several times the yield point strain than the strain caused by a much larger load; 2. Uneven cooling caused by residual stress. Residual stress in the absence of external force are under the internal self-equilibrium stress and a variety of cross-section of hot-rolled steel have this kind of residual stress, the general beam section size the greater the greater the residual stress. Residual stress is self-equilibrium, but the external force on the steel members at the next performance or have a certain influence. Such as deformation, stability, anti-fatigue, etc. may have an adverse role. 3. Hot-rolled steel products, for the thickness and the wide side of good control in this regard.热胀冷缩our well-known, because of the beginning of the hot-rolled out of even length, the thickness of all targets, and finally cooled or negative must be bad, bad side of this negative more wide wide, the thickness of the thicker, the more obvious manifestations. So for the large steel, the steel edge wide, thickness, length, angle, and the line could not be very precise requirements.

收起